Norton's theorem

 In direct-current circuit theory, Norton's theorem (aka Mayer–Norton theorem) is a simplification that can be applied to networks made of linear time-invariant resistances, voltage sources, and current sources. At a pair of terminals of the network, it can be replaced by a current source and a single resistor in parallel.

Any black box containing resistances only and voltage and current sources can be replaced by an equivalent circuit consisting of an equivalent current source in parallel connection with an equivalent resistance.

Edward Lawry Norton

For alternating current (AC) systems the theorem can be applied to reactive impedances as well as resistances.

The Norton equivalent circuit is used to represent any network of linear sources and impedances at a given frequency.

Norton's theorem and its dual, Thévenin's theorem, are widely used for circuit analysis simplification and to study circuit's initial-condition and steady-state response.

Norton's theorem was independently derived in 1926 by Siemens & Halske researcher Hans Ferdinand Mayer (1895–1980) and Bell Labs engineer Edward Lawry Norton (1898–1983).^{[1][2][3][4][5][6]}

To find the equivalent, the Norton current I_no is calculated as the current flowing at the terminals into a short circuit (zero resistance between A and B). This is I_no. The Norton resistance R_no is found by calculating the output voltage produced with no resistance connected at the terminals; equivalently, this is the resistance between the terminals with all (independent) voltage sources short-circuited and independent current sources open-circuited. This is equivalent to calculating the Thevenin resistance.

When there are dependent sources, the more general method must be used. The voltage at the terminals is calculated for an injection of a 1Amp test current at the terminals. This voltage divided by the 1 A current is the Norton impedance R_no. This method must be used if the circuit contains dependent sources, but it can be used in all cases even when there are no dependent sources.

Example of a Norton equivalent circuitEdit

1. The original circuit
2. Calculating the equivalent output current
3. Calculating the equivalent resistance
4. Design the Norton equivalent circuit

In the example, the total current I_total is given by:

${\displaystyle I_{\mathrm {total} }={15\,\mathrm {V} \over 2\,\mathrm {k} \Omega +1\,\mathrm {k} \Omega \,\|\,(1\,\mathrm {k} \Omega +1\,\mathrm {k} \Omega )}=5.625\,\mathrm {mA} .}$

The current through the load is then, using the current divider rule:

${\displaystyle I_{\mathrm {no} }={1\,\mathrm {k} \Omega +1\,\mathrm {k} \Omega \over (1\,\mathrm {k} \Omega +1\,\mathrm {k} \Omega +1\,\mathrm {k} \Omega )}\cdot I_{\mathrm {total} }}$

${\displaystyle =2/3\cdot 5.625\,\mathrm {mA} =3.75\,\mathrm {mA} .}$

And the equivalent resistance looking back into the circuit is:

${\displaystyle R_{\mathrm {no} }=1\,\mathrm {k} \Omega +(2\,\mathrm {k} \Omega \,\|\,(1\,\mathrm {k} \Omega +1\,\mathrm {k} \Omega ))=2\,\mathrm {k} \Omega .}$

So the equivalent circuit is a 3.75 mA current source in parallel with a 2 kΩ resistor.

Conversion to a Thévenin equivalentEdit

To a Thévenin equivalent

A Norton equivalent circuit is related to the Thévenin equivalent by the equations:

${\displaystyle R_{\rm {th}}=R_{\rm {no}}\!}$

${\displaystyle V_{\rm {th}}=I_{\rm {no}}R_{\rm {no}}\!}$

${\displaystyle {\frac {V_{\rm {th}}}{R_{\rm {th}}}}=I_{\rm {no}}\!}$

Queueing theoryEdit

The passive circuit equivalent of "Norton's theorem" in queuing theory is called the Chandy Herzog Woo theorem.^[3][4][7] In a reversible queueing system, it is often possible to replace an uninteresting subset of queues by a single (FCFS or PS) queue with an appropriately chosen service rate.

This article uses material from the Wikipedia article  Metasyntactic variable, which is released under the  Creative Commons Attribution-ShareAlike 3.0 Unported License.